Install Glass Pool Fencing

  • Install Glass Pool Fencing

Install glass panels and mini posts to stay safe without blocking the view. 

Gone are the days of the pool fence that fulfilled the safety regulations but did nothing to enhance the appearance of the yard. 

Today’s pool owners want a safe outdoor area that doesn’t have to compromise on looks, so modern pool fencing comes in a range of materials with slimline rails, posts and gate hardware.

Frank Gardner needed a pool fence that he could install between plastered brick columns. He chose glass panels, as they are tough and look unobtrusive.

Plan the layout

Find out what components you will need to construct a pool fence that meets council requirements.

Frank chose a fully frameless mini post system. He installed six glass panels, including one custom gate panel, with concrete footings. The fence measured 6.3 metres.

To help work out what you will need, send the supplier the dimensions and the type of system required.

They will respond with a diagram of the recommended configuration, plus a parts list and cost estimate. 

Installation checklist 

Before you start the project, make sure you’re fully prepared.

CONTACT the council to check what building regulations you will need to comply with.

CHECK THE SITE for available attachment points such as a concrete slab or footing. 

CHOOSE the fencing suitable for your site, then work out what components you will need.

ORDER the components then prepare the site as required.

Prepare the site 

This fence system requires the posts to be secured to either a 100mm thick slab or 400 x 400 x 400mm footings.

As the existing pavers had been originally laid on sand over aggregate, concrete footings had to be poured to support the new mini posts.

Frank lifted the pavers and then dug 400 x 400mm trenches through the aggregate between the columns before pouring the concrete.

‘Once the footings had been poured, I screeded a 10mm thick wet mortar bed over the concrete and then replaced the pavers,’ says Frank.

The mini posts were attached to the new footings using 8mm galvanised threaded rod, secured into the concrete with a chemical anchor.

Step 1. Lift the pavers

Work two flat drive screwdrivers into the paving joints and apply pressure to the handles to lift a paver from its location. After removing the first paver to create an opening, lift out as many pavers as required to expose the footing site.

step 1. lift the pavers, handyman magazine,

Step 2. Excavate the trenches 

Dig 400 x 400mm trenches with centrelines corresponding to the marked fence centrelines. Use a mattock or spud bar to break up the old compacted base aggregate then shovel it into a wheelbarrow for removal from the site.

step 2. excavate the trenches, handyman magazine,

Step 3. Pour the concrete footing

To make the concrete, combine 10 parts aggregate, five parts sand and two parts cement with water. Fill the trenches to the top of the old aggregate level, then use a spirit level to screed the concrete. Leave to dry then replace all the pavers on a wet mortar mix. 

step 3. pour concrete footing, handyman magazine,

Install the fencing 

Step 1. Set out the hole positions

Screw base plates to the mini posts. Remove the cover plates and use the individual mini posts to mark their hole positions. Position posts 200mm from the edges of the glass, lining up the posts accurately before drilling.

Step 2. Drill the anchor holes

Use a hammer drill with a 5mm then 10mm masonry bit to drill the anchor holes through the paving and into the concrete footing to a minimum depth of 80mm at each marked position

Step 3. Anchor the posts

Position the mini posts and check the hole alignment. Use a caulking gun to apply chemical anchor into the holes then wind in M8 ChemSet anchor studs, leaving 10mm protruding above the base plate.

Step 4. Bolt the posts

Leave the chemical anchor for about an hour to cure. Tighten the anchor studs with a socket wrench or shifter and ensure that the base of the mini post is secure. Slip a base cap over each mini post.

Step 5. Secure end brackets

Mark the fence centreline and the top and base of the glass panels on the columns. Mark the screw positions 150mm from the top and base of the panels then secure the end brackets with screws.

Step 6. Position glass panels

Working with a helper and wearing glass-gripping gloves, lift each glass panel carefully into the mini posts, making sure the rubber insert is slightly raised and not folded over. Allow the glass to slide into position.

Step 7. Secure the glass panels

Use a measuring tape to check that the glass panels are positioned correctly with equal spacing at both ends then use an Allen key to tighten the clamp section of each mini post, securing the panels firmly.

Step 8. Level the panels

Use a spirit level to check the glass panels are level and plumb. To make adjustments, loosen the nuts securing the mini post base and insert packers under the baseplate. Tighten the nuts and replace the base caps to finish.

Step 9. Hinge the gate panel

Attach the hinges to the hinge panel then release the tension. Prop the gate in position and secure it, then use the supplied tensioning lever to adjust the hinge tension so the gate closes itself. Attach the latch on the pool side.

Vote It Up: